Can I Install a Bathtub Myself? Factors to Consider As Well As Steps
Can I Install a Bathtub Myself? Factors to Consider As Well As Steps
Blog Article
What're your opinions on Installing A Bathtub?
Installing a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and occasionally, tiling abilities. Replacing an old tub with a brand-new one is likewise a moderately challenging project. If the old bathtub is readily obtainable, the project can relocate quickly; if you have to open up a wall to eliminate the old tub and place the new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will require a helper to leave the old tub and also embeded in the brand-new one. Ensure you have actually certified yourself for the work and fit attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to think about employing one prior to you begin. Opportunities are you may require an expert plumber to make tube connections.
This short article will certainly aid you mount a brand-new bathtub in your washroom if you have actually already acquired a brand-new tub and do not need to change the setup of your previous supply of water pipes.
Your devices as well as product list should consist of the following:
Preparing for the Installation
To start with, the supporting structure supplied with the bath needs to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps unit to stop stress on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing taps can be rather bothersome as a result of the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. When the supply pipes have been removed, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Before carrying on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Utilizing the two wooden boards under its feet, put the tub in the needed setting. The wooden boards are valuable in uniformly spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the level reviews degree.
To mount faucets, fit all-time low of the furthest versatile tap adapter to the ideal supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Turn on the water system as well as examine all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the bath tub as well as additionally inspect the overflow outlet and the normal electrical outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait up until the bathtub has actually been utilized at least when as this will certainly settle it into its last position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making sure that the washers are in place between the tap and the sink. Safeguard the faucet in position with the producer offered backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former kind needs to be linked to the tap finishes initially, tightening only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to crack a stiff seal, causing the water to pass through the wall between the bathroom as well as the tiling, leading to difficulties with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the movement experienced when the bathtub remains in use. The sealer can break rather early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly offered on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water-proof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate person who reads on A Step-by-Step Guide to Installing a Bathtub, I assumed sharing that post was really helpful. Do you know about someone else who is interested in Installing A Bathtub? Take a moment to share it. Thanks for your time spent reading it.
Details
Report this page